Finding your suitable readers for arduino air quality sensor is not easy. You may need consider between hundred or thousand products from many store. In this article, we make a short list of the best readers for arduino air quality sensor including detail information and customer reviews. Let’s find out which is your favorite one.
689 reviews analysed
1. HiLetgo® MQ-135 MQ135 Air Quality Sensor Hazardous Gas Detection Module For Arduino AVR
Feature
- Main chip: LM393,MQ-135 gas sensor
- With high sensitivity and good selectivity for air quality, harmful gas detection.
- With the DO switch signal (TTL) output and AO analog signal output
- Useing of high-quality double-panel design, with power instructions and TTL signal output instructions
- TTL output valid signal is low. (When the output low signal light, can be directly connected to the microcontroller or relay module)
Description
MQ-135 sensor introduction:
The gas sensitive material used with the MQ135 gas sensor is tin dioxide (SnO2), which has a lower conductivity in clean air. When contaminated gas is present in the environment
where the sensor is located, the conductivity of the sensor increases as the concentration of contaminated gas in the air increases. A simple circuit converts the change in conductivity into an output signal that corresponds to the gas concentration.
The MQ135 sensor is highly sensitive to ammonia, sulphides and benzene vapors and is also ideal for smoke and other harmful monitoring. This sensor can detect a variety of harmful gases, is a low-cost sensor for a variety of applications.
Module application:
It is suitable for the detection of harmful gases such as ammonia, aromatics, sulfides, benzene vapor, smoke and other harmful gas detection devices, gas sensor testing range of concentration: 10 to 1000ppm
Electrical performance:
Input voltage: DC5V Power consumption (current): 150mA
DO output: TTL digital quantities 0 and 1 (0.1 and 5V)
DO output: TTL digital quantities 0 and 1 (0.1 and 5V)
Dimension: 32 mm x 20 mm x 22mm
Reminded: After the sensor is powered on, you need to preheat about 20S, the measured data was stable, the sensor is a normal heating, because the internal electric wire, if the hot is not normal.
Wiring:
1. VCC: Positive power supply (5V)
2. GND: connect the negative power supply
3. DO: TTL switch signal output
4. AO: analog signal output
Package Included:
1*MQ-135 MQ135 Air Quality Sensor Hazardous Gas Detection Module
2. KOOKYE 16 in 1 Smart Home Sensor Modules Kit for Arduino Raspberry Pi DIY Professional
Feature
- SMART HOME LEARNING KIT–This kit combines the most common electronic components of smart home projects,developed specially for those beginners who are interested in Arduino and raspberry pi 3 DIY.
- THE PROFESSIONAL SMART HOME KIT–This has 16 sensors modules and delicately selected sensors to detect temperature, humidity, sound, light, infrared, motion, flame,vibration,digital touch, air pressure and many other commonly-used sensors modules.
- THE MOST COMPLETE SMART HOME KIT–This universal kit are compatible for Arduino UNO R3 / Mega2560 / Mega328 /Nano / Raspberry Pi 3, it could DIY 16 projects according to your need.
- HIGH QUALITY GUARANTEE–We eliminate many old-fashioned sensors which have low reliability and duplicate function as other sensor in the kit, the kookye modules sensor kits are choosed carefully for our user.
- DETAILED TUTORIAL ON OUR WEBSITE–Our website (http://kookye.com/?p=1573) provide step-by-step instruction, detailed circuit connection graph/video, verified sample code and library package which can save lot of user’s research time and speed up the learning progress.
3. KEYESTUDIO Pm2.5 Sensor Pm2.5 Air Particle Monitor for Arduino Mega 2560 Controller R3 Nano Micro Pro Mini Raspberry Pi
Feature
- Dust Sensor based on Sharp optics works well in detecting very delicate particle, like cigarette smoke, is a commonly used system of air purifier
- Contains IR LED and photoeletric transistor
- Arranging them with across corners can detect the reflected light of dust in the air
- It has a ultra-low power consumption(Max at 20mA, Typical at 11mA ), and can be equipped with sensors up to 7VDC
- How to use: search for “keyestudio wiki ks0196” in Google Chrome to get the wiki online tutorial for this product.
Description
Specifications:
Power Voltage: 5-7V
Working Temperature: -10℃ to 65 ℃
Current Consumption:Max 20mA
Detecting Value of Minimum Particle: 0.8μm
Sensitivity:0.5V/(0.1mg/m3)
Voltage of Cleaning Air: 0.9V(Typical)
Storage Temperature: -20℃~80℃
Service Life:5 Years
Size:62mm*32mm*20mm
Applications:
Air Purifier
Air Conditioner
Air Monitor
PM2.5 Detector
Shipping List:
Dust Sensor x 1
ZH1.5MM6-pin wire x 1
4. seeed studio Grove – Air Quality Sensor v1.3
Description
Description:
The sensor is designed for indoor air quality testing. The main gas detected is carbon monoxide, alcohol, acetone, thinner, formaldehyde and other slightly toxic gases. It is compatible with 5V and 3.3V power supply.
Feature:
Low power consumption
High sensitivity
Tiny outline
Responsive to a wide scope of target gases
Cost efficient
Durable
Compatible with 5V and 3.3V
Specification:
Sensor: Winsen MP503
Power: 5V or 3.3V
Dimension: 40x20mm
5. Eiechip9PCS/Lot Gas Detection Sensor Module MQ-2 MQ-3 MQ-4 MQ-5 MQ-6 MQ-7 MQ-8 MQ-9 MQ-135 Sensor Module Gas Sensor Starter Kit
Feature
- Gas Detection Sensor Module
- Quick response and recovery characteristics
- The dual signal output (analog output and TTL output)
- The analog output and increased with the increase of concentration, the higher the concentration higher voltage
- Has a very high sensitivity to sulfide, benzene vapor, smoke and other harmful gases
Description
Choosing Eiechip Feels Fantacy !!!
1.With signal output indicator light.
2.Size: 32mm X22mm X30mm length * width * height;
3.The main chip: LM393, MQ-x gas sensing probe;
4.Working voltage: DC 5V;
5.With signal output indicator light;
6.The dual signal output (analog output and TTL output);
7.The analog output and increased with the increase of concentration, the higher the concentration higher voltage;
8.Has a very high sensitivity to sulfide, benzene vapor, smoke and other harmful gases;
9.With a long service life and reliable stability;
10.Quick response and recovery characteristics;
11.With mounting holes, easy mounting;
12.The probe can be plug design, convenient test
Application:
For harmful gas family, environment detection device, is suitable for the detection of the ammonia, aromatic compounds, sulfide, benzene vapor, smoke and other harmful gas, gas sensitive element concentration range: 10 to 1000ppm provides reference cases.
Package Included:
MQ-2 MQ-3 MQ-4 MQ-5 MQ-6 MQ-7 MQ-8 MQ-9 MQ-135 each one.
6. KEYESTUDIO CCS811 Carbon Dioxide CO2 VOCs Air Quality Gas Temperature Sensor Module for Arduino
Feature
- This sensor mainly uses the CCS811B chip. It is an ultra-low-power miniature digital gas sensor that can detect a wide range of volatile organic compounds (TVOCs), including equivalent carbon dioxide (eCO2) and metal oxide (MOX) levels.
- Equivalent carbon dioxide (eCO2) is measured in the range of 400 to 8192 ppm (parts per million), and various volatile organic compounds (TVOC) ranges from 0 to 1187 ppb (parts per billion).
- The sensor comes with a 10K precision 1% NTC thermistor, which can be used to test the specific temperature in the environment. It’s housed in a very compact package.
- This sensor module is compatible for the arduino microcontrollers as well as raspberry pi etc.
- How to use: Search for “keyestudio wiki KS0457” in Google Chrome to get the wiki online tutorial for this product.
Description
Technical Parameters
Working voltage: DC 5V
Working current: 30mA
Maximum power: 46mW
eCO2 measurement range: 400-8192 ppm
TVOC measurement range: 0 to 1187 ppb
Working temperature: -25 ~ +65℃
Interface: 7pin (2.54mm pitch)
Positioning hole diameter: 3mm
Dimensions: 36mm*20mm*7mm
Environmental attributes: ROHS
7. flashtree PM Sensor SDS011 High Precision PM2.5 Air Quality Detection Sensor Module Super Dust Sensors Digital Output for Arduino
8. Adafruit CCS811 Air Quality Sensor Breakout – VOC and eCO2
Description
Breathe easy – we finally have an I2C VOC/eCO2 sensor in the Adafruit shop! Add air quality monitoring to your project and with an Adafruit CCS811 Air Quality Sensor Breakout. This sensor from AMS is a gas sensor that can detect a wide range of Volatile Organic Compounds (VOCs) and is intended for indoor air quality monitoring. When connected to your microcontroller (running our library code) it will return a Total Volatile Organic Compound (TVOC) reading and an equivalent carbon dioxide reading (eCO2) over I2C. There is also an onboard thermistor that can be used to calculate the local ambient temperature.
The CCS811 has a ‘standard’ hot-plate MOX sensor, as well as a small microcontroller that controls power to the plate, reads the analog voltage, and provides an I2C interface to read from.
Conclusion
By our suggestions above, we hope that you can found Arduino Air Quality Sensor for you.Please don’t forget to share your experience by comment in this post. Thank you!
